Видео

Viene venduto anche in italia ?

Hi where did you get mattress for it ?

Great bed build I purchased a Thor scope van here in the US the bed is CRAP I’ve been looking for ideas to redo it this video helped a lot THANK YOU for sharing I’m gonna put my Cnc to work 👍🏽

What wood and edging are you using?

Great job, well done. 👍🏆

Brilliant, much better than big take over rock n roll bed. This is the way for my T6👍🏆simple but effective. Cheers .

Brilliant, much better than big take over rock n roll bed. This is the way for my T6👍🏆

will this van without the sliding door work as a 5 seater

GB plates are obsolete.

Absolutely fantastic conversion. I am going to get one and convert. Are you able to provide plans etc 👍

Looking forward to seeing the finished van! Andrew and Rona

Excellent design

Excellent this is just what I’ve been looking to build in my T4 many thanks👍

Great vehicle, well presented.

Pitty the engine is wet belt garbage 30k miles it will explode

The annoying music adds nothing to this video

Merhaba, ahşap parçaların kesim ölçüleri var mı?

thanks a lot for your sharing this Video....lgmario

Tbh this is such bs set up…it’s pathetic. The be westslia pull and be done, is the only sensible way

That’s great but I have 3 wires coming from my pump! Blue, red and Yellow. Any ideas?

sehr schicker Bus ihr habt das drauf in England

This is such a beautiful, roomy, well built, with every possibility covered 1. How much is this? 2. Where can it be bought? 3. Is it left hand drive? 4. Does it have an electric connect cable outside? 5. Can solar panels be added?

Perfect job,well done! I have only one question,pls answer.Are the support legs in front are exactly the same hight as the base,or they are with few millimetres less to avoid scrubbing onto the floor and ensure smooth slide ?

Meu Deus que lindo cara 😍

Been watching a few more of your videos Dan. Took out the Rock and Roll bed on my T6 (hopefully I can sell it 🤞) and started building the pull-out bed based on your design. Your window curtains and surrounds are next level so I think I will try and do that too at some point. Brilliant channel and what a craftsman you are!!

Dan and his campers are brilliant solutions for practical travelling and camping on a budget. I'm recommending him. Is it in stock please and what is the price? Could a larger table be hooked on? Are Satnav and tail gate shower or larger water containers possible?

I am amazed you do not have ventilation for the gas cylinder.on the outside of the van.

My dream.

What type of stupid dumb video is this?

Brilliant design. I have decided the rock and roll bed is just not want I want in my campervan so I taking it out. I will use your design to construct a new setup. Thank you for sharing all of this information. I'll make sure to use you Amazon afillate links when ordered various bits

Excellent conversion is it possible to do the same for a Skoda Yeti 4x4 fitted with a panoramic sliding roof?

Do Kangoo owners search for VW Caddy builds to see what they are doing? I'm a Caddy owner. Lol

Hello, Very nice work! Could you please tell me who makes those back doors window blinds? Thanks in advance.

The hookup flex from the pitch hookup point to the vertical should be a minimum of 4 mm2 blue sheath. The Earth single earth lead to the chassis should be a minimum of 10mm2 and is connected to the Earth terminal in the vans CU which should have a 80amp / 30 milliamp RCD as the main point of isolation a 6amp MCB for the lights and a 16 amp MCB for the sockets . Lights should be wired in 1.0 mm2 TW&E and the sockets wired in 2.5mm2 TW&E you are also required by law to have smoke detector hard wired on the own circuit and 6amp MCB. Your lights are 12v LEDs you will need to use a pelv LED driver which will convert the 240v mains to 12v dc .

Why not just buy a sofa bed form Argos ? 200 quid , bolt it down , job done

Hi, Does the bed/seat slide forward to be positioned like a second set of seats behind the front seats when travelling, rather than it being all the way back there. Thanks

Brilliant videos, extremely helpful

Hi Dan is this a bespoke Kitchen or a purchased one really like the look of the kitchen!

Question - does using the bed slats make that much of a difference on support/comfort vs flat pieces of wood?

Thank you for this beautiful video

Where does the motor part of the refrigerator provide air flow?

Thanks for the video. Is there a way to wire a submersible pump to a normal tap (non-microswitch) with a manual 12v rocker switch? I purchased a tap not realizing it should have a microswitch and am trying to figure out how to make it work. I'd prefer to use a submersible 12v pump if possible, I don't want to go the whale pump route

Beautiful! I’ve just got a 2014 Transit custom that I’ve had lots of problems with due to the crooks I bought it off. I wish I had one of these. My leisure battery decided to vent gases and it was in the bed area, not good. Does this battery area have a vented and boxed area for safety. Honestly I’ve been through so much crap, but I’ve been unlucky, I’d have another transit done like this in a flash! Your accent sounds very Wigan? Do you do electric checks on camper vans?

Very nice

Doing a similar build now any chance u still have the pattern for overhead locker or even would tou sell a pre cut one ?